English version

Домой   Новости   Радио   Карточки   Кодграберы   Мобилки   Телефония   АТС   Пейджинг   Транки   Жучки   Форум


Google

ICOM U16 HAND PROGRAMMING


I need a ICOM FL63 CW filter for my IC735 transceiver.

Best regards, MALE (nukleus@mail333.com), leader of Hackersrussia crew


NEED A PASSWORD? CLICK HERE !


Cheap electronics on largest online auction:

Icom U16 Programming

  ---------------------------------------------------------------------------
	The U16 is made programmable by moving a jumper inside the unit, then try holding [FUNC] down
	and entering 159357. You are now in programming mode. Exit program mode with [FUNC] + [CLR].
	Function + 159357 Enter programming mode (Function = [FUNC] key)
	Function + [1] PL (CTCSS) Encoder tones (1-37)
	+ [2] PL (CTCSS) Decoder tones (1-37)
	1 = 67.0 2 = 71.9 3 = 74.4 4 = 77.0 5 = 79.7
	6 = 82.5 7 = 85.4 8 = 88.5 9 = 91.5 10= 94.8
	11=100.0 12=103.5 13=107.2 14=110.9 15=114.8
	16=118.8 17=123.0 18=127.3 19=131.8 20=136.5
	21=141.3 22=146.2 23=151.4 24=156.7 25=162.2
	26=167.9 27=173.8 28=179.9 29=186.2 30=192.8
	31=203.5 32=210.7 33=218.1 34=225.7 35=233.6
	36=241.8 37=250.3 (Tone 97.4 Not Available)
	+ [3] ?
	+ [4] Delta + / Delta - offset, 5 digits
	+ [5] Frequency, 5 digits (400 MHz +)
	+ [6] ?
	+ [7] Special Channel Number (allows alias ch. 17-99 number)
	+ [8] Transmit timeout enable.
	+ [9] TI - Transmit Inhibit
	+ [SCAN] Priority Scan/Ch Scan
	+ [S.CH] Channel Masking
	+ [CLEAR] End programming mode
 ---------------------------------------------------------------------------
	Channel select: Standard method (up/down arrows or CH# + [ENTER]) Frequency: Hold [FUNC],
	Press [5], enter 6 dig freq, [ENTER], Release [FUNC] Rx CTCSS: Hold [FUNC], Press [2], enter 2
	dig code, [ENTER], Release [FUNC] Tx CTCSS: Hold [FUNC], Press [1], enter 2 
	dig code, [ENTER], Release [FUNC] Offset Freq: Hold [FUNC], Press [4], use [#] for up offset, [*] for down offset, then
	enter freq to offset by (ie: [#] [0] [0] [0] [0] [0] for no offset, [#] [0] [5] [0] [0] [0] for
	the standard +5MHz UHF offset), [ENTER], Release [FUNC] Timeout Timer: Hold [FUNC], [8],
	Release [FUNC] Tx Inhibit: Hold [FUNC], [9], Release [FUNC] Special Ch. #: Hold [FUNC], Press
	[7], enter the special channel number (17-99), [ENTER], Release [FUNC] Data Transfer MASTER:
	Hold [FUNC], [BEEP], Release [FUNC] SLAVE: Hold [FUNC] with power off, turn on, Release [FUNC]
 ---------------------------------------------------------------------------

Cheap electronics on largest online auction:


NEED A PASSWORD? CLICK HERE !


MALE